Call Now For Your FREE Estimate: 515-266-4660 | 24/7 Emergency Service Available

Peace of Mind Service Plans

Get Peace of Mind AND Save Money? What Could Be Better Than That?


Invest in one of the most comprehensive service agreements available anywhere. With this agreement, you'll be considered a Preferred Customer which entitles you to absolute priority service, extended warranties, cash discounts, and most importantly: Peace of Mind.

The purpose of this plan is to provide your family with enhanced equipment safety and efficiency as well as extend the life of your equipment. Your family will also appreciate knowing that your equipment has been tested for deadly, odorless, poisonous carbon monoxide gas. This agreement entitles you to benefit from our exclusive 23-point precision tune-up and professional cleaning (PTPC)

Precision Furnace Tune-up Benefits:
  • Lower utility bills.
  • Extended equipment life.
  • Fewer repairs, breakdowns, and improved system reliability.
  • Peace of mind for you and your family.
  • Increased heating capacity.
  • Priority service scheduling.
Precision Air-Conditioning Tune-up Benefits:
  • Lower utility bills by reducing energy consumption and waste.
  • Extended equipment life.
  • Peace of mind for you and your family.
  • Fewer repairs, and improved system reliability.
  • Increased cooling capacity and efficiency.
Our Exclusive Precision Tune-Up Procedure Includes, As Needed:
  1. Inspect and tighten all electrical connections and terminals.
  2. Remove, clean, and adjust the main gas burners.
  3. Remove, clean, and adjust ignition/pilot assembly.
  4. Thoroughly brush and vacuum clean the heat-exchanger(s) and combustion chambers.
  5. Inspect heat-exchanger(s) & combustion chambers for cracks, rusting, or problem areas.
  6. Vacuum out blower compartment; return airdrop and surrounding area. (No duct cleaning)
  7. Clean all return air grills throughout the home.
  8. Inspect the flue assembly and test the flue gas drafting mechanism.
  9. Test and inspect all furnace safety controls.
  10. Test, record, and adjust gas pressure.
  11. Replace or clean standard air filters.
  12. Remove and clean blower motor, drive mechanism, and fan assembly.
  13. Lubricate all fan motors and all moving parts.
  14. Measure and adjust the blower for correct airflow.
  15. Adjust all dampers and set the proper blower speed(s).
  16. Clean, level, test, and calibrate the thermostat.
  17. Measure and record heating system output.
  18. Inspect and test thermocouple output as well as the pilot safety switch.
  19. Measure and record electrical voltage, amperage, and component resistance.
  20. Inspect and test all system transformers, relays, contactors, and controls. Measure performance
  21. Repair minor air leaks in plenum and return airdrop.
  22. Perform a complete and thorough, room-by-room, electronic carbon monoxide check of the entire house.
  23. Advise customer on other ways to reduce energy consumption, improve safety and enhance comfort.
  1. Chemically clean and thoroughly wash condenser coil(s).
  2. Thoroughly clean or replace standard air filter(s).
  3. Wash and level condensing unit for proper motor and bearing wear.
  4. Lubricate motor and fan bearings as well as other moving parts as necessary.
  5. Clean and inspect the evaporator coil and drain pan when readily accessible.
  6. Clean and inspect condensate drain lines and fittings.
  7. Clean, level, and calibrate the thermostat.
  8. Adjust and thoroughly clean blower motor and fan assembly as needed.
  9. Inspect, tighten and test all electrical connections. This includes the disconnect switch.
  10. Inspect all cooling system electrical wires, connectors, and terminals.
  11. Test system starting and running capacitors.
  12. Test all controls, switches, relays, transformers, contactors, motors, and fans.
  13. Measure the starting and running amperes, line voltage, and control voltage.
  14. Test system-starting capabilities.
  15. Test system for proper airflow and air delivery.
  16. Inspect and adjust all safety controls.
  17. Monitor refrigerant (Freon) pressures and temperatures.
  18. Test and record super-heat and sub-cooling. Compare with factory specifications.
  19. Adjust Freon metering control device per factory/manufactures recommendations.
  20. Test and measure the air-conditioning system for proper production and capacity.
  21. Monitor fan motors and compressor operating temperatures.
  22. Apply weather-resistant protective coating to the outside unit. (Condenser)
  23. Complete and present a full written report.
  • Get a Free Estimate:
    Please enter your first name

    Please enter your last name

    Invalid Input

    Please enter your email address

    Please enter your phone number

    Please enter a message

  • Zero Percent Financing - Apply Now!
  • 100% Guaranteed Satisfaction - Contact Us for Details
Get Money Saving Tips
Join our email list for money saving tips, ideas and promotions.
  • We Sell Quality Products From:
  • Trust Des Moines Comfort:
    HVAC SaveNate CertifiedEnergy Star
    Des Moines Comfort Inc, Heating & Air Conditioning, Des Moines, IA
  • Des Moines Comfort Heating, Cooling & Geothermal • 2703 E. Grand Ave, Des Moines, Iowa 50317 • 515-266-4660
© 2020 Des Moines Comfort. All Rights Reserved. • Privacy Policy • Website Design by Idea Rocket Labs Marketing